| Availability: | |
|---|---|
| Quantity: | |
Valve Plate
Blait
The valve plate sits between the cylinder and the cylinder head of a reciprocating compressor and does one job: it controls which way the gas flows. Two thin, flexible reed valves are mounted on the plate; on the piston's downward stroke the suction-side reed lifts and refrigerant gas enters the cylinder, and on the upward stroke the discharge-side reed lifts and compressed gas leaves it. That happens hundreds of times per minute at working pressure, so the plate and reeds are wear parts — and the most common first service on an aging piston compressor.
When the reeds wear, the failures are gradual and easy to miss: cooling capacity drops, discharge temperature climbs, the unit cycles short, and the valve area starts to knock. By the time the compressor seizes, the repair bill is a whole new machine. Replacing the valve plate set restores the machine's breathing in a short service job instead — and the parts cost a small fraction of a replacement compressor.

Main components of the compressor valve plate: plate body, reed valves, rivet pins, holes
Ours are stainless steel plates with stainless reed valves, supplied as a suction + discharge set for the cylinder head, made by the compressor manufacturer. They follow the third-generation valve-plate design used across the Blait piston line, which improves exhaust efficiency and shock resistance.

Signs your compressor needs a valve plate refresh
The parent machines run where Blait compressors run: cold storage and blast freezing, commercial refrigeration, cold chain and process cooling, and marine and fishing-vessel refrigeration on the type-approved compressor models.
Item | Value |
|---|---|
Material | Stainless steel — plate body and reed valves |
Supply unit | Suction valve plate + discharge valve plate, supplied as a set per head |
Design | Third-generation valve-plate design: improved exhaust efficiency, enhanced shock resistance |
Fits | Blait single-stage semi-hermetic piston refrigeration compressors, T-Series (BTF range) and second-generation (YBF range) |
Matching | Model-specific: each compressor model has its own plate. Send the full model number from the nameplate and we confirm the match before order |
Dimensions | Not published on this page — the exact plate is confirmed against your model before order |
Packing | Protective export packaging; lead time confirmed with your order |
Three-step model matching guide for ordering the right valve plate
Ordering is a three-step check, and it protects you from the one thing that matters with this part:
Read the nameplate. Find the full model code on your compressor, e.g. BTF4VCS-6.3Z (T-Series) or YBF4FC-3.2Z (second-generation range).
Send it to us — a photo of the head helps, but the model number is what we work from.
We confirm the matching plate against your model and quote the set (suction + discharge). Nothing ships before that confirmation.
The two generations share the same physical base family, which is why one plate family serves both lines — but the exact plate is still per model, and that matching step is done for you, not left to guesswork.
Supply and quality: stainless steel, set supply, first-party manufacturing, parent machine type approval
First-party spare. The plate is made by the compressor manufacturer, to the same design standard as the machine it fits.
Parent-machine approval, honestly stated. The Blait piston compressor line carries China Classification Society type approval for the compressor as a whole machine. The valve plate is a service part for that machine; it is not a separately certified item, and we do not claim certification for the part itself.
Buyer value in one line. You keep the machine you have — motor, body, connections and installation untouched — and restore capacity with a parts job, not a replacement.
If your compressor is showing the classic worn-valve signs — capacity loss, high discharge temperature, short cycling, valve noise — send us the model number and we will confirm the set.
What is a compressor valve plate?
The valve plate is the part in the cylinder head of a reciprocating (piston) compressor. It carries the flexible reed valves that open and close with each piston stroke, letting refrigerant gas in on the suction stroke and pushing it out on the discharge stroke. It is one of the most common wear parts on an aging compressor.
Do you sell the suction and discharge plates separately or as a set?
As a set. The suction valve plate and the discharge valve plate are supplied together per cylinder head, so the two reed groups stay matched.
What material are the valve plates made of?
Stainless steel — both the plate body and the flexible reed valves.
Which compressors do these valve plates fit?
Blait single-stage semi-hermetic piston refrigeration compressors: the T-Series (BTF range) and the second-generation (YBF range). Different models use different plates, so this page does not list a one-fits-all part number.
How do I know which plate my compressor needs?
Send us the full model number from the compressor nameplate, for example BTF4VCS-6.3Z or YBF4FC-3.2Z. We check it against the model, confirm the matching plate and quote the set before anything ships.
Why replace the valve plate instead of the whole compressor?
Worn reeds show up as reduced capacity, higher discharge temperature and short cycling. A plate job restores capacity in a short service job and costs a small fraction of a new machine — the motor, body, connections and installation all stay where they are.
What signs mean my compressor's valves are wearing out?
The classic four: cooling capacity dropping, discharge temperature climbing, the unit cycling short, and an abnormal knocking or hissing from the head area. Any two of the four is worth a valve inspection.
Is the valve plate CCS approved?
The Blait piston compressor line carries China Classification Society type approval for the compressor as a whole machine. The valve plate is a service part for that machine; it is not a separately certified item, and we do not claim certification for the part itself.
What if the plate does not match my head exactly?
It will not seal — the plate must match the head's port layout exactly. That is why every order is confirmed against your model number first; the matching check is included, not an extra step.
What else do I need for the replacement?
Normally the plate set plus the head gasket, and a cleaning of the head face and ports. We confirm the full parts list for your model with the quote, so the head is opened once, not twice.